blog
Home blog

blog

  • Why the rewinding of the slitting machine always goes off track?
    • March 29, 2024

    The reason why the slitting machine's winding always goes off track: 1. Problem of equipment deviation 2. Air leakage occurs in parts of the reel 3. Is the pressure at both ends of the reel consistent? What cannot be ignored during production is to pay attention to changes in product tension, etc. Slitting machine is a mechanical equipment that cuts wide-width paper, mica tape or film into multipl...

  • What is a twin screw air compressor?
    • February 01, 2024

    The screw air compressor is an oil-injected single-stage twin-screw compressor. It adopts high-efficiency pulley (or shaft) transmission to drive the main engine to rotate for air compression. It cools and lubricates the compression chamber of the main engine through oil injection, and the air discharged from the compression chamber The gas mixed with oil undergoes coarse and fine separation to se...

  • Differences in processing range between engraving and milling machines and machining centers.
    • January 19, 2024

    Machining centers are unable to process small molds with small tools, and the cost is high. The advantage of the engraving machine is engraving, but if the hardness of the processed material is relatively high, it will be unable to do its job. The emergence of engraving and milling machines can be said to be the shortcomings of both.  The machining center can realize the centralized processin...

  • Characteristics of the chromium plating process and classification of plating solutions?
    • December 22, 2023

    In addition to the common characteristics with other plating types, the chromium plating process also has the following special points: (1) The dispersion ability of the plating solution is poor. To obtain a uniform coating, special fixtures (including pictographic anodes) must be designed according to the geometry of the parts. ); (2) The current efficiency is low (generally 13~16%), a large amou...

  • What are the advantages and characteristics of gravity casting machines?
    • November 29, 2023

    1. There are few pores inside the casting, and the rigidity of the product after heat treatment can be greatly improved, even exceeding that of die-casting products. 2. The product has low density. Relying on liquid self-gravity molding, the density of low-pressure casting machine products is lower than that of die casting, and its strength is also slightly lower, but its elongation is higher. 3. ...

  • What are the basic principles of electroplating equipment?
    • November 03, 2023

    The research and development, design, manufacturing, sales and service of electroplating equipment and ultrasonic cleaning equipment are integrated. Electroplating is an electrochemical process and an oxidation-reduction process. The basic process of electroplating is to immerse parts in a solution of metal salts as a cathode. , the metal plate serves as the anode, and after connecting to the DC p...

  • Difference between boring and milling machine and milling and boring machine.
    • October 18, 2023

    Milling machine refers to a gantry milling machine that mainly uses milling cutters to process various surfaces on workpieces. Usually the rotational motion of the milling cutter is the main motion, and the motion of the workpiece (and) the milling cutter is the feed motion. Boring machine gantry milling machine, milling and boring machine and boring machine are one of them. Boring machines can al...

  • What is the working principle of CNC machine tools?
    • October 09, 2023

    The working principle of CNC machine tools is: the computer in the CNC device performs a series of processing on the information recorded in the form of numerical and character encoding through the input device, and then executes the machine tool spindle and feed through the servo system and programmable controller. The mechanism issues instructions, and the machine tool body follows these instruc...

  • SQSK12450 Horizontal twelve-axis CNC technical parameters
    • September 28, 2023

    Functional characteristics : 1、The workpiece is clamped and formed in one step, and servo feed is used to complete the entire process to improve product stability and accuracy. 2、This machine tool adopts a twelve-axis power turret head and a high-precision ball and line roller combination. It can mill, drill, ream, and tap at the same time, completing multiple sets of processes to improve producti...

  • What is the Induction Furnace?
    • September 08, 2023

    An electric furnace that uses the induction electrothermal effect of the warehouse to heat or melt the warehouse. There are three types of AC power used in induction furnaces: power frequency (50 or 60 Hz), intermediate frequency (150~10000 Hz) and high frequency (10000 Hz). The main components of the induction furnace are the inductor, the furnace body, the power supply, the capacitor and the con...

    A total of

    15

    pages

D&S Automatic Co.,Ltd. located at the China plumbing town of Fujian Nan'an,It is a professional machine company. We supply you modern facilities,such as faucet, valve, brass fitting, cartridge, brass fittings, teflon tape and all kinds of machines. 

Copyright © 2024 D&S Automatic Co.,Ltd.. All Rights Reserved.

IPv6 network supported

top

Leave A Message

Leave A Message

    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

  • #
  • #
  • #